Category: Armour

Bituminous products soften in contact with petroleum solvent and mineral oils. The product has good resistance to dilute acids and alkalis.

COMPOSITION: A bitumen / resin blend containing SBS Polymer – Rubber Chips –
Fibre Reinforcement – Aggregate – Extender & Adhesion Agent.
STORAGE: Store in a cool dry place preferably under cover and away from direct sunlight.
PACKAGING: Silicone or Poly-silicone lined sacks – 20 / 25kgs Net.

FLAMMABILITY LIMITS
Upper – Not applicable.
Lower – Not applicable.

EXTINGUISHING MEDIA
Small Fire – Foam / Water Fog.
Large Fire – Foam / Dry Powder / CO² / Sand / Earth.

SUPPLY CLASSIFICATION
Not dangerous for supply.

Armourband^® presents no acute health hazard at ambient temperature. However, as these materials are normally handled at elevated temperatures when their physical state changes to a liquid, the bitumens present in these products give of fumes which are undesirable to inhale as very small quantities of HYDROGEN SULPHIDE may be present in the bitumen.

RECOMMENDED PROTECTIVE CLOTHING:
Overalls, Goggles / Visor and Closed Safety Boots when handling hot product.
INHALATION:
Inhalation of the vapours should be avoided.
FIRST AID:
Remove the affected person to fresh aid. If breathing has stopped administer artificial respiration. Give cardiac massage if necessary. If the person is breathing but unconscious place in the recovery position. Obtain medical assistance immediately.
SKIN CONTACT:
Bituminous products present no acute health hazards to the skin other than burning when handling at elevated temperatures.
FIRST AID:
Flush the contaminated skin with cold water. DO NOT ATTEMPT TO REMOVE THE BITUMEN. Cover the burn with a sterile dressing. Do not apply any medication to the affected part. Obtain medical attention immediately.
EYE CONTACT:
Contact with fumes may cause irritation and redness.
FIRST AID:
Irrigate with copious amounts of water – 10 / 20 minutes and seek medical advice immediately.
PRECAUTIONS:
Avoid contact with the skin by use of suitable protective clothing.
TRANSPORTATION:
Not classified as dangerous for transportation.

The Bridge Joint Compound (BJC) system can accommodate a movement range of ± 25mm in a standard APJ installation of 600mm width. The system is resistant to plastic flow at surface temperatures of 50°c and is a registered binder system for use in Asphaltic Plug Joints (APJ).

APPROVALS: Highways Agency Number 029

Bituminous products soften in contact with petroleum solvent and mineral oils. The product has good resistance to dilute acids and alkalis.

STORAGE: Store in a cool dry place away from direct sunlight.
COMPOSITION: A polymer modified bitumen containing graded extender with adhesion agents.

The aggregate should be nominally 20mm (18-20-22) and either Basalt or Granite Type as listed in BS 812.
Where the joint depth is expected to be less than 75mm the aggregate should be a 50:50 blend of 20 & 14mm.

Aggregate Properties:
PSV 55+
AAV 4 – 6

* Do not exceed the maximum safe heating temperature.
* Do not allow the hot material to come into contact with water as the product will react violently.
* Always wear the recommended protective clothing – see below.

Armourjoint^® presents no acute health hazard at ambient temperature. However, as these materials are normally handled at elevated temperatures when their physical state changes to a liquid, the bitumens present in these products give of fumes which are undesirable to inhale as very small quantities of HYDROGEN SULPHIDE may be present in the bitumen.

RECOMMENDED PROTECTIVE CLOTHING:
High Visibility Jacket, Hard Safety Helmet, Overalls, Goggles/Visor, Armlet Gloves and Closed Safety Boots at all times when handling hot product.
INHALATION:
Inhalation of the vapours should be avoided.
INHALATION FIRST AID:
Remove the affected person to fresh aid. If breathing has stopped administer artificial respiration. Give cardiac massage if necessary. If the person is breathing but unconscious place in the recovery position. Obtain medical assistance immediately.
SKIN CONTACT:
Bituminous products present no acute health hazards to the skin other than burning when handling at elevated temperatures.
SKIN CONTACT FIRST AID:
Flush the contaminated skin with cold water. DO NOT ATTEMPT TO REMOVE THE BITUMEN. Cover the burn with a sterile dressing. Do not apply any medication to the affected part. Obtain medical attention immediately.
EYE CONTACT:
Contact with fumes may cause irritation and redness.
EYE CONTACT FIRST AID:
Irrigate with copious amounts of water for 10 / 20 minutes and seek medical advice immediately.
PRECAUTIONS:
Avoid contact with the skin by use of suitable protective clothing.
TRANSPORTATION:
Not classified as dangerous for transportation.

Latest Revision – December 2021

Bituminous products soften in contact with petroleum solvent and mineral oils. The product has good resistance to dilute acids and alkalis.

STORAGE: Store in a cool dry place preferably under cover and away from direct sunlight.
COMPOSITION: A polymer modified bitumen containing graded extender with adhesion agents.
PACKAGING: Silicon lined boxes 15kgs Net.

* Do not exceed the maximum safe heating temperature.
* Do not allow the hot material to come into contact with water as the product will react violently.
* Always wear the recommended protective clothing – see below.

Armourjoint^® BP02a presents no acute health hazard at ambient temperature. However, as these materials are normally handled at elevated temperatures when their physical state changes to a liquid, the bitumens present in these products give of fumes which are undesirable to inhale as very small quantities of HYDROGEN SULPHIDE may be present in the bitumen.

RECOMMENDED PROTECTIVE CLOTHING:
High Visibility Jacket, Hard Safety Helmet, Overalls, Goggles/Visor, Armlet Gloves and Closed Safety Boots at all times when handling hot product.
INHALATION:
Inhalation of the vapours should be avoided.
INHALATION FIRST AID:
Remove the affected person to fresh aid. If breathing has stopped administer artificial respiration. Give cardiac massage if necessary. If the person is breathing but unconscious place in the recovery position. Obtain medical assistance immediately.
SKIN CONTACT:
Bituminous products present no acute health hazards to the skin other than burning when handling at elevated temperatures.
SKIN CONTACT FIRST AID:
Flush the contaminated skin with cold water. DO NOT ATTEMPT TO REMOVE THE BITUMEN. Cover the burn with a sterile dressing. Do not apply any medication to the affected part. Obtain medical attention immediately.
EYE CONTACT:
Contact with fumes may cause irritation and redness.
EYE CONTACT FIRST AID:
Irrigate with copious amounts of water for 10/20 minutes and seek medical advice immediately.
PRECAUTIONS:
Avoid contact with the skin by use of suitable protective clothing.
TRANSPORTATION:
Not classified as dangerous for transportation.

Latest Revision – December 2021

Bituminous products soften in contact with petroleum solvent and mineral oils. The product has good resistance to dilute acids and alkalis.

STORAGE: Store in a cool dry place preferably under cover and away from direct sunlight.
COMPOSITION: A polymer modified bitumen containing graded extender with adhesion agents.
PACKAGING: Poly Lined Silicone sacks – 20kgs Net.

*Do not exceed the maximum safe heating temperature.
*Do not allow the hot material to come into contact with water as the product will react violently.
*Always wear the recommended protective clothing – see below.

Armourjoint^® BP02B presents no acute health hazard at ambient temperature. However, as these materials are normally handled at elevated temperatures when their physical state changes to a liquid, the bitumens present in these products give of fumes which are undesirable to inhale as very small quantities of HYDROGEN SULPHIDE may be present in the bitumen.

RECOMMENDED PROTECTIVE CLOTHING:
High Visibility Jacket, Hard Safety Helmet, Overalls, Goggles / Visor, Armlet Gloves and Closed Safety Boots AT ALL TIMES when handling hot product.
INHALATION:
Inhalation of the vapours should be avoided.
INHALATION FIRST AID:
Remove the affected person to fresh aid. If breathing has stopped administer artificial respiration. Give cardiac massage if necessary. If the person is breathing but unconscious place in the recovery position. Obtain medical assistance immediately.
SKIN CONTACT:
Bituminous products present no acute health hazards to the skin other than burning when handling at elevated temperatures.
SKIN CONTACT FIRST AID:
Flush the contaminated skin with cold water. DO NOT ATTEMPT TO REMOVE THE BITUMEN. Cover the burn with a sterile dressing. Do not apply any medication to the affected part. Obtain medical attention immediately.
EYE CONTACT:
Contact with fumes may cause irritation and redness.
EYE CONTACT FIRST AID:
Irrigate with copious amounts of water for 10/20 minutes and seek medical advice immediately.
PRECAUTIONS:
Avoid contact with the skin by use of suitable protective clothing.
TRANSPORTATION:
Not classified as dangerous for transportation.
FURTHER INFORMATION:
Additional information on the product is given in the system Safety Data Sheet and Installation Method Statement or by contacting Walker Sealants Ltd.

Latest Revision – December 2021

Bituminous products soften in contact with petroleum solvent and mineral oils. The product has good resistance to dilute acids and alkalis.

STORAGE: Store in a cool dry place preferably under cover and away from direct sunlight.
COMPOSITION: A polymer modified bitumen containing graded extender with adhesion agents.
PACKAGING: Poly Lined Silicone sacks – 20kgs Net.

*Do not exceed the maximum safe heating temperature.
*Do not allow the hot material to come into contact with water as the product will react violently.
*Always wear the recommended protective clothing – see below.

Armourjoint^® BP02HM presents no acute health hazard at ambient temperature. However, as these materials are normally handled at elevated temperatures when their physical state changes to a liquid, the bitumens present in these products give of fumes which are undesirable to inhale as very small quantities of HYDROGEN SULPHIDE may be present in the bitumen.

RECOMMENDED PROTECTIVE CLOTHING:
High Visibility Jacket, Hard Safety Helmet, Overalls, Goggles/Visor, Armlet Gloves and Closed Safety Boots AT ALL TIMES when handling hot product.
INHALATION:
Inhalation of the vapours should be avoided.
INHALATION FIRST AID:
Remove the affected person to fresh aid. If breathing has stopped administer artificial respiration. Give cardiac massage if necessary. If the person is breathing but unconscious place in the recovery position. Obtain medical assistance immediately.
SKIN CONTACT:
Bituminous products present no acute health hazards to the skin other than burning when handling at elevated temperatures.
SKIN CONTACT FIRST AID:
Flush the contaminated skin with cold water. DO NOT ATTEMPT TO REMOVE THE BITUMEN. Cover the burn with a sterile dressing. Do not apply any medication to the affected part. Obtain medical attention immediately.
EYE CONTACT:
Contact with fumes may cause irritation and redness.
EYE CONTACT FIRST AID:
Irrigate with copious amounts of water for 10 / 20 minutes and seek medical advice immediately.
PRECAUTIONS:
Avoid contact with the skin by use of suitable protective clothing.
TRANSPORTATION:
Not classified as dangerous for transportation.
FURTHER INFORMATION:
Additional information on the product is given in the system Safety Data Sheet and Installation Method Statement or by contacting Walker Sealants Ltd.

Latest Revision – December 2021

Bituminous products soften in contact with petroleum solvent and mineral oils. The product has good resistance to dilute acids and alkalis.

COMPOSITION: A polymer modified bituminous compound containing aggregate (OBS60) and adhesion agents.
STORAGE: Store in a cool dry place preferably under cover and away from direct sunlight.
PACKAGING: Silicone or Poly-silicone lined sacks – 20 / 25Kgs Net.

*Do not exceed the maximum safe heating temperature.
*Do not allow the hot material to come into contact with water as the product will react violently.
*Always wear the recommended protective clothing – see below.

Armourlay^® BP03 & 03A presents no acute health hazard at ambient temperature. However, as these materials are normally handled at elevated temperatures when they’re physical state changes to a liquid, the bitumens present in these products give of fumes, which are undesirable to inhale as very small quantities of HYDROGEN SULPHIDE may be present in the bitumen.

RECOMMENDED PROTECTIVE CLOTHING:
High Visibility Jacket, Hard Safety Helmet, Overalls, Goggles/Visor, Armlet Gloves and Closed Safety Boots AT ALL TIMES when handling hot product.

INHALATION:
Inhalation of the vapours should be avoided.
INHALATION FIRST AID:
Remove the affected person to fresh aid. If breathing has stopped administer artificial respiration. Give cardiac massage if necessary. If the person is breathing but unconscious place in the recovery position. Obtain medical assistance immediately.
SKIN CONTACT:
Bituminous products present no acute health hazards to the skin other than burning when handling at elevated temperatures.
SKIN CONTACT FIRST AID:
Flush the contaminated skin with cold water. DO NOT ATTEMPT TO REMOVE THE BITUMEN. Cover the burn with a sterile dressing. Do not apply any medication to the affected part. Obtain medical attention immediately.
EYE CONTACT:
Contact with fumes may cause irritation and redness.
EYE CONTACT FIRST AID:
Irrigate with copious amounts of water for 10 / 20 minutes and seek medical advice immediately.
PRECAUTIONS:
Avoid contact with the skin by use of suitable protective clothing.
TRANSPORTATION:
Not classified as dangerous for transportation.
FURTHER INFORMATION:
Additional information on the product is given in the system Safety Data Sheet and Installation Method Statement or by contacting Walker Sealants Ltd.

Latest Revision – December 2021

Armourlay^® Tropical BP03 & 03A grades are polymer modified bituminous crack repair materials which are designed to achieve SRV values of ≥ 45 and ≥ 60 respectively. The products are formulated to resist trafficking and deformation in temperate climates and are suitable for application on all types of asphalt and concrete surfacing.

USES:
•Overbanding & Crack Sealing Repairs
•Kerb Sealing Work
ADVANTAGES:
•Fast and effective, minimises traffic disruption
•Highly ductile, prevents further deterioration
•Increases pavements serviceable life
•Easy to install and cost effective

Bituminous products soften in contact with petroleum solvent and mineral oils. The product has good resistance to dilute acids and alkalis.

STORAGE: Store in a cool dry place preferably under cover and away from direct sunlight.
COMPOSITION: A polymer modified bituminous compound containing aggregate (OBS60) and adhesion agents.
PACKAGING: Silicone or Poly-silicone lined sacks – 20 / 25kgs Net.

*Do not exceed the maximum safe heating temperature.
*Do not allow the hot material to come into contact with water as the product will react violently.
*Always wear the recommended protective clothing – see below.

Armourlay^® Tropical BP03 & 03A presents no acute health hazard at ambient temperature. However, as these materials are normally handled at elevated temperatures when their physical state changes to a liquid, the bitumens present in these products give of fumes which are undesirable to inhale as very small quantities of HYDROGEN SULPHIDE may be present in the bitumen.

RECOMMENDED PROTECTIVE CLOTHING:
High Visibility Jacket, Hard Safety Helmet, Overalls, Goggles / Visor, Armlet Gloves and Closed Safety Boots AT ALL TIMES when handling hot product.
INHALATION:
Inhalation of the vapours should be avoided.
INHALATION FIRST AID:
Remove the affected person to fresh aid. If breathing has stopped administer artificial respiration. Give cardiac massage if necessary. If the person is breathing but unconscious place in the recovery position. Obtain medical assistance immediately.
SKIN CONTACT:
Bituminous products present no acute health hazards to the skin other than burning when handling at elevated temperatures.
SKIN CONTACT FIRST AID:
Flush the contaminated skin with cold water. DO NOT ATTEMPT TO REMOVE THE BITUMEN. Cover the burn with a sterile dressing. Do not apply any medication to the affected part. Obtain medical attention immediately.
EYE CONTACT:
Contact with fumes may cause irritation and redness.
EYE CONTACT FIRST AID:
Irrigate with copious amounts of water for 10 / 20 minutes and seek medical advice immediately.
PRECAUTIONS:
Avoid contact with the skin by use of suitable protective clothing.
TRANSPORTATION:
Not classified as dangerous for transportation.
FURTHER INFORMATION:
Additional information on the product is given in the system Safety Data Sheet and Installation Method Statement or by contacting Walker Sealants Ltd.

Latest Revision – December 2021

The Armourscreed^® AS50 system is a polymer modified bituminous compound incorporating graded high PSV aggregates, rubber granules, fibre reinforcement, extender and adhesion agents.

USES
• Inlay Crack Repair System
• Concrete Repair System
• Stress Absorbing Membrane
• Kerb Sealing Applications
ADVANTAGES
• Prevents further deterioration
• Increases the pavements effective life
• Suitable for both asphalt and concrete surfaces
• Fast and effective installation minimises traffic disruption
• Suitable for application throughout the year
• Cost effective

Armourscreed^® AS50 has been installed successfully on numerous civil and military airfields including:
• RAF Lakenheath
• RAF Mildenhall
• RAF Brize Norton
• RAF Yeovilton
• Farnborough Airport
• Stanstead Airport

Bituminous products soften in contact with petroleum solvent and mineral oils. The product has good resistance to dilute acids and alkalis.

COMPOSITION: A polymer modified bituminous blend incorporating rubber granules, fibre reinforcement, high PSV aggregate, extender and adhesion agent.
STORAGE: Store in a cool dry place preferably under cover and away from direct sunlight.
PACKAGING: Multiply silicone or Poly-silicone bags – 20 / 25kgs Net.

*Do not exceed the maximum safe heating temperature.
*Do not allow the hot material to come into contact with water as the product will react violently.
* Always wear the recommended protective clothing – see below.

Armourscreed^® AS50 presents no acute health hazard at ambient temperature, however as these materials are normally handled at elevated temperatures when their physical state changes to a liquid, the bitumens present in these products give of fumes which are undesirable to inhale as very small quantities of HYDROGEN SULPHIDE may be present in the bitumen.

RECOMMENDED PROTECTIVE CLOTHING:
Overalls, Goggles / Visor, Armlet Gloves and Closed Safety Boots AT ALL TIMES when handling hot product.
INHALATION:
Inhalation of the vapours should be avoided.
INHALATION FIRST AID:
Remove the affected person to fresh aid. If breathing has stopped administer artificial respiration. Give cardiac massage if necessary. If the person is breathing but unconscious place in the recovery position. Obtain medical assistance immediately.
SKIN CONTACT:
Bituminous products present no acute health hazards to the skin other than burning when handling at elevated temperatures.
SKIN CONTACT FIRST AID:
Flush the contaminated skin with cold water. DO NOT ATTEMPT TO REMOVE THE BITUMEN. Cover the burn with a sterile dressing. Do not apply any medication to the affected part. Obtain medical attention immediately.
EYE CONTACT:
Contact with fumes may cause irritation and redness.
EYE CONTACT FIRST AID:
Irrigate with copious amounts of water for 10 / 20 minutes and seek medical advice immediately.
PRECAUTIONS:
Avoid contact with the skin by use of suitable protective clothing.
TRANSPORTATION:
Not classified as dangerous for transportation.
FURTHER INFORMATION:
Additional information on the product is given in the system Safety Data Sheet and Installation Method Statement or by contacting Walker Sealants Ltd.

Latest Revision – June 2024

The Armourscreed^® AS100 system is a polymer modified bituminous compound incorporating graded high PSV aggregates, rubber granules, fibre reinforcement, extender and adhesion agents.

USES
• Inlay Repair System
• Concrete Repair System
• Stress Absorbing Membrane Interlayer
• Kerb Sealing Work
ADVANTAGES
• Prevents further deterioration
• Increases the pavements effective life
• Suitable for both asphalt and concrete surfaces
• Fast and effective installation minimises traffic disruption
• Suitable for application throughout the year
• Cost effective

Complies with the requirements of the BBA / HAPAS Guideline Document for Crack Sealing Systems for Highways – Grade F.

Bituminous products soften in contact with petroleum solvent and mineral oils. The product has good resistance to dilute acids and alkalis.

STORAGE: Store in a cool dry place preferably under cover and away from direct sunlight.
COMPOSITION: A blended polymer modified bitumen compound incorporating rubber granules, fibre reinforcement, aggregates extender & adhesion agents.
PACKAGING: Multiply Silicone or Poly-silicone lined bags – 20 / 25kgs Net.

*Do not exceed the maximum safe heating temperature.
*Do not allow the hot material to come into contact with water as the product will react violently.
*Always wear the recommended protective clothing – see below.

Armourscreed^® AS100 presents no acute health hazard at ambient temperature, however as these materials are normally handled at elevated temperatures when their physical state changes to a liquid, the bitumens present in these products give of fumes which are undesirable to inhale as very small quantities of HYDROGEN SULPHIDE may be present in the bitumen.

RECOMMENDED PROTECTIVE CLOTHING:
Overalls, Goggles / Visor, Heat Resistant Gloves and Closed Safety Boots AT ALL TIMES when handling hot product.
TRANSPORTATION:
Not classified as dangerous for transportation.
INHALATION:
Inhalation of the vapours should be avoided.
INHALATION FIRST AID:
Remove the affected person to fresh aid. If breathing has stopped administer artificial respiration. Give cardiac massage if necessary. If the person is breathing but unconscious place in the recovery position. Obtain medical assistance immediately.
SKIN CONTACT:
Bituminous products present no acute health hazards to the skin other than burning when handling at elevated temperatures.
SKIN CONTACT FIRST AID:
Flush the contaminated skin with cold water. DO NOT ATTEMPT TO REMOVE THE BITUMEN. Cover the burn with a sterile dressing. Do not apply any medication to the affected part. Obtain medical attention immediately.
EYE CONTACT:
Contact with fumes may cause irritation and redness.
EYE CONTACT FIRST AID:
Irrigate with copious amounts of water for 10 / 20 minutes and seek medical advice immediately.
PRECAUTIONS:
Avoid contact with the skin by use of suitable protective clothing.
TRANSPORTATION:
Not classified as dangerous for transportation.
FURTHER INFORMATION:
Additional information on the product is given in the system Safety Data Sheet and Installation Method Statement or by contacting Walker Sealants Ltd.

Latest Revision – December 2021

Bituminous products soften in contact with petroleum solvent and mineral oils. The product has good resistance to dilute acids and alkalis.

COMPOSITION: A blend of polymer modified bitumen and fine limestone.
STORAGE: Store in a cool dry place preferably under cover and away from direct sunlight.
PACKAGING: Multiply silicone lined sacks – 25kgs Net.

*Do not exceed the maximum safe heating temperature.
*Do not allow the hot material to come into contact with water as the product will react violently.
*Always wear the recommended protective clothing – see below.

Armourgrout presents no acute health hazard at ambient temperature. However, as these materials are normally handled at elevated temperatures when their physical state changes to a liquid, the bitumens present in these products give of fumes which are undesirable to inhale as very small quantities of HYDROGEN SULPHIDE may be present in the bitumen.

RECOMMENDED PROTECTIVE CLOTHING:
Overalls, Goggles / Visor, Armlet Gloves and Closed Safety Boots AT ALL TIMES when handling hot product.
INHALATION:
Inhalation of the vapours should be avoided.
INHALATION FIRST AID:
Remove the affected person to fresh aid. If breathing has stopped administer artificial respiration. Give cardiac massage if necessary. If the person is breathing but unconscious place in the recovery position. Obtain medical assistance immediately.
SKIN CONTACT:
Bituminous products present no acute health hazards to the skin other than burning when handling at elevated temperatures.
SKIN CONTACT FIRST AID:
Flush the contaminated skin with cold water. DO NOT ATTEMPT TO REMOVE THE BITUMEN. Cover the burn with a sterile dressing. Do not apply any medication to the affected part. Obtain medical attention immediately.
EYE CONTACT:
Contact with fumes may cause irritation and redness.
EYE CONTACT FIRST AID:
Irrigate with copious amounts of water for 10 / 20 minutes and seek medical advice immediately.
PRECAUTIONS:
Avoid contact with the skin by use of suitable protective clothing.
TRANSPORTATION:
Not classified as dangerous for transportation.
FURTHER INFORMATION:
Additional information on the product is given in the system Safety Data Sheet and Installation Method Statement or by contacting Walker Sealants Ltd.

Latest Revision – December 2021

Bituminous products soften in contact with petroleum solvent and mineral oils. The product has good resistance to dilute acids and alkalis.

COMPOSITION: A blend of oxidised bitumen and fine limestone.
STORAGE: Store in a cool dry place preferably under cover and away from direct sunlight.
PACKAGING: Multiply silicone lined sacks – 25kgs.

* Do not exceed the maximum safe heating temperature.
* Do not allow the hot material to come into contact with water as the product will react violently.
* Always wear the recommended protective clothing. – see below.

Bituminous products present no acute health hazard at ambient temperature. However, as these materials are normally handled at elevated temperatures when their physical state changes to a liquid, the bitumens present in these products give off fumes which are undesirable to inhale as very small quantities of HYDROGEN SULPHIDE may be present in the bitumen.

RECOMMENDED PROTECTIVE CLOTHING:
Overalls, Goggles / Visor, Armlet Gloves and Closed Safety Boots AT ALL TIMES when handling hot product.
INHALATION:
Inhalation of the vapours should be avoided.
INHALATION FIRST AID:
Remove the affected person to fresh aid. If breathing has stopped administer artificial respiration. Give cardiac massage if necessary. If the person is breathing but unconscious place in the recovery position. Obtain medical assistance immediately.
SKIN CONTACT:
Bituminous products present no acute health hazards to the skin other than burning when handling at elevated temperatures.
SKIN CONTACT FIRST AID:
Flush the contaminated skin with cold water. DO NOT ATTEMPT TO REMOVE THE BITUMEN. Cover the burn with a sterile dressing. Do not apply any medication to the affected part. Obtain medical attention immediately.
EYE CONTACT:
Contact with fumes may cause irritation and redness.
EYE CONTACT FIRST AID:
Irrigate with copious amounts of water for 10 / 20 minutes and seek medical advice immediately.
PRECAUTIONS:
Avoid contact with the skin by use of suitable protective clothing.
TRANSPORTATION:
Not classified as dangerous for transportation.
FURTHER INFORMATION:
Additional information on the product is given in the system Safety Data Sheet and Installation Method Statement or by contacting Walker Sealants Ltd.

Latest Revision – December 2021

USES
Sealing and maintenance of joints in concrete and asphalt carriageways and airfield pavements.

ADVANTAGES
* Conforms to the DOT Specification for Highway Works clauses 1016 and 1017.
* Resilient to the ingress of dirt and grit associated with trafficked pavements.
* Resistant to plastic flow over a wide range of service temperatures.
* Good adhesion to concrete and asphalt surfaces.

Bituminous products soften in contact with petroleum solvent and mineral oils. The product has good resistance to dilute acids and alkalis.

COMPOSITION: A polymer modified bituminous joint sealing compound with graded extender and adhesion agent.
STORAGE: Store in a cool dry place preferably under cover and away from direct sunlight.
PACKAGING: Silicone boxes or Poly-silicone bags 15 / 20Kgs – Net.
PRIMER: Bitumen or Rubber Resin primer on concrete surfaces. No primer required on asphalt surfaces.

FLAMMABILITY LIMITS
Upper – Not applicable.
Lower – Not applicable.

EXTINGUISHING MEDIA
Small Fire – Foam / Water Fog.
Large Fire – Foam / Dry Powder / CO² / Sand / Earth.

SUPPLY CLASSIFICATION
Not dangerous for supply.

Armourseal^® N1 BP08 presents no acute health hazard at ambient temperature. However, as these materials are normally handled at elevated temperatures when their physical state changes to a liquid, the bitumens present in these products give of fumes which are undesirable to inhale as very small quantities of HYDROGEN SULPHIDE may be present in the bitumen.

RECOMMENDED PROTECTIVE CLOTHING
Overalls, Goggles / Visor and Closed Safety Boots when handling hot product.
INHALATION
Inhalation of the vapours should be avoided.
INHALATION FIRST AID
Remove the affected person to fresh air. If breathing has stopped administer artificial respiration. Give cardiac massage if necessary. If the person is breathing but unconscious place in the recovery position. Obtain medical assistance immediately.
SKIN CONTACT FIRST AID
Bituminous products present no acute health hazards to the skin other than burning when handling at elevated temperatures.
FIRST AID
Flush the contaminated skin with cold water. DO NOT ATTEMPT TO REMOVE THE BITUMEN. Cover the burn with a sterile dressing. Do not apply any medication to the affected part. Obtain medical attention immediately.
EYE CONTACT
Contact with fumes may cause irritation and redness.
FIRST AID
Irrigate with copious amounts of water for 10 / 20 minutes and seek medical advice immediately.
PRECAUTIONS
Avoid contact with the skin by use of suitable protective clothing.
TRANSPORTATION
Not classified as dangerous for transportation
FURTHER INFORMATION:
Additional information on the product is given in the system Safety Data Sheet and Installation Method Statement or by contacting Walker Sealants Ltd.

Bituminous products soften in contact with petroleum solvent and mineral oils. The product has good resistance to dilute acids and alkalis.

COMPOSITION: A polymer modified bituminous joint sealing compound with graded extender and adhesion agent.
STORAGE: Store in a cool dry place preferably under cover and away from direct sunlight.
PACKAGING: Silicone boxes or Poly – Silicone bags 15 / 20Kgs – Net.
PRIMER: Bitumen or Rubber Resin primer on concrete surfaces. No primer required on asphalt surfaces.

FLAMMABILITY LIMITS
Upper – Not applicable.
Lower – Not applicable.

EXTINGUISHING MEDIA
Small Fire – Foam / Water Fog.
Large Fire – Foam / Dry Powder / CO² / Sand / Earth.

SUPPLY CLASSIFICATION
Not dangerous for supply.

Bituminous products present no acute health hazard at ambient temperature. However, as these materials are normally handled at elevated temperatures when their physical state changes to a liquid, the bitumens present in these products give of fumes which are undesirable to inhale as very small quantities of HYDROGEN SULPHIDE may be present in the bitumen.

RECOMMENDED PROTECTIVE CLOTHING
Overalls, Goggles / Visor and Closed Safety Boots AT ALL TIMES when handling hot product.
INHALATION
Inhalation of the vapours should be avoided.
INHALATION FIRST AID
Remove the affected person to fresh air. If breathing has stopped administer artificial respiration. Give cardiac massage if necessary. If the person is breathing but unconscious place in the recovery position. Obtain medical assistance immediately.
SKIN CONTACT
Bituminous products present no acute health hazards to the skin other than burning when handling at elevated temperatures.
SKIN CONTACT FIRST AID
Flush the contaminated skin with cold water. DO NOT ATTEMPT TO REMOVE THE BITUMEN. Cover the burn with a sterile dressing. Do not apply any medication to the affected part. Obtain medical attention immediately.
EYE CONTACT
Contact with fumes may cause irritation and redness.
EYE CONTACT FIRST AID
Irrigate with copious amounts of water for 10 / 20 minutes and seek medical advice immediately.
PRECAUTIONS
Avoid contact with the skin by use of suitable protective clothing.
TRANSPORTATION
Not classified as dangerous for transportation.
FURTHER INFORMATION:
Additional information on the product is given in the system Safety Data Sheet and Installation Method Statement or by contacting Walker Sealants Ltd.

Latest Revision – December 2021

A hot poured, low extension rubber/bitumen joint sealant suitable for internal and external horizontal jointing.

USES: A rubber / bitumen modified sealant for low movement joints in concrete and asphalt floors. Armourseal^® BP11 is formulated to a high softening point to resist trafficking and deformation at high temperatures.

Bituminous products soften in contact with petroleum solvent and mineral oils. The product has good resistance to dilute acids and alkalis.

COMPOSITION: A polymer modified bituminous joint sealing compound with graded extender and adhesion agent.
STORAGE: Store in a col dry place preferably under cover and away from direct sunlight.
PACKAGING: Silicone boxes or Poly-silicone bags 15 / 20kgs – Net.
PRIMER: Bitumen or Rubber Resin primer on concrete surfaces. No primer required on asphalt surfaces.

FLAMMABILITY LIMITS
Upper – Not applicable.
Lower – Not applicable.

EXTINGUISHING MEDIA
Small Fire – Foam / Water Fog.
Large Fire – Foam / Dry Powder / CO² / Sand / Earth.

SUPPLY CLASSIFICATION
Not dangerous for supply.

Bituminous products present no acute health hazard at ambient temperature. However, as these materials are normally handled at elevated temperatures when their physical state changes to a liquid, the bitumens present in these products give off fumes which are undesirable to inhale as very small quantities of HYDROGEN SULPHIDE may be present in the bitumen.

RECOMMENDED PROTECTIVE CLOTHING
Overalls, Goggles / Visor and Closed Safety Boots AT ALL TIMES when handling hot product.
INHALATION
Inhalation of the vapours should be avoided.
INHALATION FIRST AID
Remove the affected person to fresh air. If breathing has stopped administer artificial respiration. Give cardiac massage if necessary. If the person is breathing but unconscious place in the recovery position. Obtain medical assistance immediately.
SKIN CONTACT
Bituminous products present no acute health hazards to the skin other than burning when handling at elevated temperatures.
SKIN CONTACT FIRST AID
Flush the contaminated skin with cold water. DO NOT ATTEMPT TO REMOVE THE BITUMEN. Cover the burn with a sterile dressing. Do not apply any medication to the affected part. Obtain medical attention immediately.
EYE CONTACT
Contact with fumes may cause irritation and redness.
EYE CONTACT FIRST AID
Irrigate with copious amounts of water for 10 / 20 minutes and seek medical advice immediately.
PRECAUTIONS
Avoid contact with the skin by use of suitable protective clothing.
TRANSPORTATION
Not classified as dangerous for transportation.
FURTHER INFORMATION:
Additional information on the product is given in the system Safety Data Sheet and Installation Method Statement or by contacting Walker Sealants Ltd.

Latest Revision – December 2021

The binder shall conform to BS3690 Part 1 Grade 70 Pen and shall constitute 25 – 30% of the mixture.

The fine limestone shall be of suitable grade of which a minimum of 80% shall pass a 75um test sieve and shall constitute 70 – 75% of the mixture.

Bituminous products soften in contact with petroleum solvent and mineral oils. The product has good resistance to dilute acids and alkalis.

COMPOSITION: A blend of penetration grade bitumen and fine limestone.
STORAGE: Store in a cool dry place preferably under cover and away from direct sunlight.
PACKAGING: Multiply silicone lined sacks – 25kgs Net.

* Do not exceed the maximum safe heating temperature.
* Do not allow the hot material to come into contact with water as the product will react violently.
* Always wear the recommended protective clothing – see below.

FLAMMABILITY LIMITS
Upper – Not applicable.
Lower – Not applicable.

EXTINGUISHING MEDIA
Small Fire – Foam / Water Fog.
Large Fire – Foam / Dry Powder / CO² / Sand / Earth.

SUPPLY CLASSIFICATION
Not dangerous for supply.

Bituminous products present no acute health hazard at ambient temperature. However, as these materials are normally handled at elevated temperatures when their physical state changes to a liquid, the bitumens present in these products give off fumes which are undesirable to inhale as very small quantities of HYDROGEN SULPHIDE may be present in the bitumen.

RECOMMENDED PROTECTIVE CLOTHING
Overalls, Goggles / Visor, Gloves and Closed Safety Boots AT ALL TIMES when handling hot products.
INHALATION
Inhalation of the vapours should be avoided.
INHALATION FIRST AID
Remove the affected person to fresh aid. If breathing has stopped administer artificial respiration. Give cardiac massage if necessary. If the person is breathing but unconscious place in the recovery position. Obtain medical assistance immediately.
SKIN CONTACT
Bituminous products present no acute health hazards to the skin other than burning when handling at elevated temperatures.
SKIN CONTACT FIRST AID
Flush the contaminated skin with cold water. DO NOT ATTEMPT TO REMOVE THE BITUMEN. Cover the burn with a sterile dressing. Do not apply any medication to the affected part. Obtain medical attention immediately.
EYE CONTACT
Contact with fumes may cause irritation and redness.
EYE CONTACT FIRST AID
Irrigate with copious amounts of water for 10 / 20 minutes and seek medical advice immediately.
PRECAUTIONS
Avoid contact with the skin by use of suitable protective clothing.
TRANSPORTATION
Not classified as dangerous for transportation.
FURTHER INFORMATION:
Additional information on the product is given in the system Safety Data Sheet and Installation Method Statement or by contacting Walker Sealants Ltd.

Latest Revision – December 2021

Bituminous products soften in contact with petroleum solvent and mineral oils. The product has good resistance to dilute acids and alkalis.

COMPOSITION: Straight run penetration grade bitumen.
STORAGE: Store in a cool dry place preferably under cover and away from direct sunlight.
PACKAGING: Silicone lined boxes – 12kgs Net.

* Do not exceed the maximum safe heating temperature.
* Do not allow the hot material to come into contact with water as the product will react violently.
* Always wear the recommended protective clothing – see below.

FLAMMABILITY LIMITS
Upper – Not applicable.
Lower – Not applicable.

EXTINGUISHING MEDIA
Small Fire – Foam / Water Fog.
Large Fire – Foam / Dry Powder / CO² / Sand / Earth.

SUPPLY CLASSIFICATION
Not dangerous for supply.